SH5141 AI Glow Wire Tester
The SH5141 AI Glow Wire Tester is designed in accordance with IEC60695-2-10. The standard-based glow wire tip simulates the thermal stress produced by glowing elements or overload resistors and assesses the sample’s fire hazard characteristics. The test is applicable to the materials in electronics products, household appliances, etc.
AI Features:
AI Flame Detection & Auto Timing I. The Sunho AI Visual System would detect the exact moment of flame ignition/extinction II. The Ti(ignition) Te(extinction) would be simultaneously recorded, and the test result(flame-duration time) would be automatically calculated and displayed. AI Temperature-Rise & Maintenance I. Before the test, the glow wire tip would be automatically heated to the test temperature(preset on screen) in 3-5min. II. During the test, the Sunho AI Circuit could minimize the test temperature error by quickly responding to the I-V fluctuation.
Technical Features:
PLC Control + 7-Inch Screen (touch) Temperature Range: 500℃-1000℃
Temperature Precision: ≤±10℃
Glow Wire Tip: Φ4mm (77％Ni 20％Cr)
Application Force: 0.95N (±0.1N)
Penetration Depth: 7mm(±0.5mm)
Application Time: 0-999.9s
Timing Mode: Auto/Manual
1mm Ni-Cr SheathedThermocouples (Type-K)
Calibration Function: temperature-rise curve of the glow wire tip
Standard-Based Fume Hood: ≥0.5m³
Accessories: remote control (1 pcs) pine board(1 pcs) silk layer(1 sheet) silver foil(1 pcs)
SH5241 Tracking Index(CTI) Tester
The SH5241 AI Tracking Index Tester is designed in accordance with IEC60112 The test apparatus conducts tests to assess the tracking index(CTI/PTI) of insulation materials, which shows its resistance to tracking under moist conditions.
AI Dropping Control:
Drops digitally controlled by a high-precision stepping motor, minimizing the fluctuation caused by the environment AI I-V Regulation:
The Sunho AI Circuit adopts a semi-closed-loop control mechanism, which response to environmental fluctuation quickly by regulating the I-V value.
Technical Features:
PLC Control + 7-Inch Screen (touch)
Electrodes Material: Half-Platinum/Pure-Platinum(optional)
Electrodes Dimension : (5±0.1)mm×(2±0.1)mm×(≥12)mm
Electrodes Position: angle 60°±5°, horizontal distance 4mm±0.1mm
Test Voltage Range: 100V-600V (auto-regulated)
Max. Short-Circuit Current: 1.0A (auto-regulated)
AI Drop Control (high-precision stepping motor)
Equipped with remote controller.
Fume Hood: ≥0.5m3
SH5341 AI Horizontal-Vertical Flaming Tester
The SH5341 Horizontal-Vertical Flame Tester is designed in accordance with IEC60112 / UL94 standards. The test apparatus conducts vertical and horizontal flame tests of materials, to assess the HB-V classification of materials.
AI Features
AI Visual Before the flame application, the Laser Sample Detector would detect the exact sample’s X-Y position, and the burner would automatically move to the test position based on the X-Y coordinates.
AI Flame Detection & Auto Timing
The Sunho AI Visual System would detect the exact moment of flame ignition/extinction
The Afterflame/Afterglow Time would be automatically recorded/calculated.
Technical Features
PLC Control + 7-Inch Screen (touch)
Burner Bore Diameter: Φ9.5±0.3mm
Burner Length: 100mm±10mm
Flame-Height Range: 20mm-175mm(by flame-regulation valve)
Test Angle: 0°/20°/45°
Test Mode: HB Mode/ V&VTM Mode/ 5V Mode
Timing: Auto Mode / Manual Mode
Burner Positioning: Auto Mode / Manual Mode
SH5441 Needle-Flame Tester
The SH5441 Needle-Flame Tester is designed in accordance with BS EN IEC 60695-11-5 / UL 94 standards The test apparatus simulates the small-flame effect resulting from fault conditions, assessing the materials’ fire hazard characteristics.
AI Features
AI Visual Before the flame application, the Laser Sample Detector would detect the exact sample’s X-Y position, and the burner would automatically move to the test position based on the X-Y coordinates. AI Flame Detection & Auto Timing I. The Sunho AI Visual System would detect the exact moment of flame ignition/extinction II. The Flame Holding Time/Afterburn Time would be automatically recorded/calculated
Technical Features
PLC Control+7-Inch Screen Display(touch)
Burner Bore Diameter: Φ0.5mm
Burner Length: 35mm
Flame-Height: 12mm(regulated by valve button)
Flame-height measuring gauge (1 pcs)
Flame-temp. measuring system: 100℃±5℃~700℃±3℃
Ignition Angle: 0°/45° preset
Test Mode: 2 Modes Available
Burner Positioning Mode: Auto/Manual
Timing: Auto/Manual
Over-Temp. Protection System
Accessories: silk layer(1 sheet) pine board(1 pcs) ignition gun(1 pcs) remote control(1 pcs) screen-protection shield(1 pcs) BRS-17B buckle(1 pcs) etc.
SH5706 Intelligent Oxygen Index Analyzer
The SH5706 Intelligent Oxygen Index Analyzer is designed in accordance with ISO 4589-2/4589-3, ASTM D 2863 The test apparatus assesses the minimum oxygen concentration required to support the materials’ combustion(OI value).
Applicability
Burning Behaviour Evaluation The OI test evaluates the burning behavior of cables, plastic materials(or any other polymer materials) Fireproof Quality Inspection The OI test evaluates the fire protection quality of flame-retardants in materials. Research and Developing The OI test assists in the development, monitoring consistency, or pre-selection of materials.
AI Features
AI O2 Percentage Control The Oxygen percentage(%) could be pre-selected on the 7-inch screen/Desktop. Following that, the AI Airflow Feedback Control System would pump the O2/N2 mixture into the chamber, detecting the real-time O2 percentage, and regulating the O2/N2 airflow until it is stabilized to the preset percentage.
(This interface is for demonstration purposes only)
Technical Features
2 Models Available: Desktop Version / TouchScreen Version
Equipped with 2 Heat-resistance glass chimneys: inside diameter＞φ95mm, height 500mm(approx.).
Timing Range: 999s±0.25s. High-accuracy gas concentration sensor: the real-time display of oxygen/nitrogen concentration.(%) Oxygen concentration: measuring limits 0%-45%. 7 inches LCD touch screen: parameters including flow rate, oxygen concentration, timing, test result, etc. are displayed on the screen. Burner: diameter Φ2mm, flame height: 16mm. Sample holder Ⅰ(for self-supporting test specimens): all stainless steel, support the specimen vertically on the central axis of the chimney Sample holder Ⅱ(for non-self-supporting test specimens): all stainless steel, supports the specimen by both vertical edges.
